Table of Contents
Preface ...............................................................................................................................1
Chapter 1 Installation........................................................................................................2
Unpacking............................................................................................................................................. 2
Connecting the LCD Monitor and Base ................................................................................................ 2
Viewing Angle Adjustment................................................................................................................... 2
Detaching LCD Monitor from Its Stand................................................................................................ 3
Interface for Arm Applications ............................................................................................................. 3
Connecting the Display to your Computer ............................................................................................ 3
Connecting the AC Power ..................................................................................................................... 3
Setting Up the LCD Monitor................................................................................................................. 3
Power Management System .................................................................................................................. 4
Chapter 2 Display Controls ...............................................................................................4
User Controls ........................................................................................................................................ 4
Adjusting the Monitor's Display............................................................................................................ 4
Function Description............................................................................................................................. 5
Chapter 3 Technical Information .....................................................................................6
Specifications........................................................................................................................................ 6
Standard Timing Table.......................................................................................................................... 7
Troubleshooting .................................................................................................................................... 8
Preface
This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has
been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The
information in this document is subject to change without notice. This document contains proprietary information
protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.
FCC Statement Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturers may void the user's authority to
operate this equipment.
NOTE
A shielded-type signal cord is required in order to meet the FCC emission limits and also to prevent interference
to the radio and television reception. It is essential that only the supplied signal cord be used.
Canadian DOC Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B repecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
1
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained for future use.
1. To clean LCD Monitor screen;
-- Power off LCD Monitor and unplug the AC Cord.
-- Spray a non-solvent cleaning solution onto a rag.
-- Gently clean the screen with dampened rag.
2. Do not place the LCD Monitor near a window. Exposing the monitor to rain water, moisture or sunlight can
severely damage it.
3. Do not apply pressure to the LCD screen. Excess pressure may cause permanent damage to the display.
4. Do not remove the cover or attempt to service this unit by yourself. Servicing of any nature should be
performed by an authorized technician.
5. Store LCD Monitor in a room with a room temperature of -20° ~ 60°C (or -4° ~ 140°F). Storing the LCD
Monitor outside this range could result in permanent damage.
6. If any of the following occurs, immediately unplug your monitor and call an authorized technician.
*
*
*
Monitor to PC signal cable is frayed or damaged.
Liquid spilled into LCD Monitor or the monitor has been exposed to rain.
LCD Monitor or the case is damaged.
7. A certified line is required to connect this device to a power outlet. For a nominal current up to 6A and a device
weight above 3 kg, a line not lighter than H05VV-F, 3G, 0.75 mm2 must be used.
Chapter 1 Installation
Unpacking
Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer.
You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has
enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some
ventilation is needed to ensure that the Monitor does not become too hot.
After you unpack the LCD Monitor, make sure that the following items were included in the box:
*
*
*
LCD Monitor
1.5M Monitor-to-PC signal Cable
Base
*
*
User's Manual
1.8M Power Cord
If you find that any of these items is missing or appears damaged, contact your dealer immediately.
Connecting the LCD Monitor and Base
When you open the box to take the base and put on
the desk first. Then connect the LCD Monitor and
base please.(See fig.1-1 )
Figure 1-1
Viewing Angle Adjustment
The LCD Monitor is designed to allow users to have
a comfortable viewing angle. The viewing angle can
be adjusted from -5°to +30°.(See fig. 1-2)
Figure 1-2
Warning
Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting
this will result in damaging the Monitor and Monitor stand.
2
Detaching LCD Monitor from Its Stand
1. Unscrew screws of the hinge bracket
2. Remove the stand from LCD monitor
(See fig. 1-3)
Figure 1-3
Interface for Arm Applications
Before installing to mounting device, please refer to
Fig.1-3.
The rear of this LCD display has four integrated 4 mm, 0.7
pitches threaded nuts, as well as four 5 mm access holes in
the plastic covering as illustrated in Figure 1-4. These
specifications meet the VESA Flat Panel Monitor
Physical Mounting Interface Standard (paragraphs 2.1
and 2.1.3, version 1, dated 13 November 1997).
Figure 1-4
Connecting the Display to your Computer
1. Power off your computer.
2. Connect the signal cable to the VGA port on your PC.
3. Make sure connection are secure.
Figure 1-5
Attention
This device must be connected to an off-the-shelf video cable in order to comply with FCC
regulations. A ferrite-core interface cable is included in the LCD Monitor package.
This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is
used.
Connecting the AC Power
1. Connect the power cord to the Monitor AC socket.
(See Fig. 1-6)
2. Connect the plug Pin of power cord to an AC power
source.
Figure 1-6
Setting Up the LCD Monitor
1. Make sure the AC power cord is connected to the LCD Monitor.
2. Turn on the LCD Monitor's power switch, located on the bezel of the monitor.
3
Power Management System
This LCD Monitor complies with the VESA DPMS (version 1.0) Power Management guidelines. The
VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync.
signal.
When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power
LED indicator will light yellow.
Chapter 2 Display Controls
User Controls
A brief description and the location of all LCD Monitor function controls and indicators:
Figure 2-1
Press the power switch to switch the monitor ON/OFF.
1
2
DC Power Switch
LED lights Green color --- Power is ON.
LED lights Yellow --- Monitor is in "Power Saving Mode".
LED is off --- Power is OFF.
DC Power-On
Indicator
Press either left or right control button for OSD (On Screen Display)
menu selection.
Press the left button to decrease the OSD setting and press the right
button to increase the OSD setting.
Function Select
Buttons
Adjustment Control
Buttons
3
4
Adjusting the Monitor's Display
The monitor has four function control buttons to select among functions shown on OSD
menu, designed for easy user-viewing environments.
OSD Function Menu
To access OSD Main menu, simply press one of
the Function Select control buttons, and the menu
diagram will pop up on the screen as shown on Fig.
2-2:
Continue pressing the Function Select buttons to
scroll through the entire menu items ,then press
Adjustment Control buttons to adjust content of
selected item.
Figure 2-2
Attention
Firmware revision may have been updated into a latest version while the version number shown on
all OSD menus in this manual will stay as Ver. 1.00MHB.
4
Function Description
Icon
Function
Function Description
Brightness
This function increases or decreases the brightness of the image.
This function increases or decreases the difference between the dark and light
color.
Contrast
H-Position
V-Position
This function shifts the entire display image left or right.
This function shifts the entire display image up or down.
A total of 32 scales (0 to 100) are available to adjust the focus and clarity of
the display.
Phase
Clock
This function carries a frequency tracking feature that offers the user to have
better stability and clarity. Increasing Clock value can be up to +127 scales.
The number of decreasing Clock (minus) is depend on the input timing.
Auto Adjustment This function will adjust the display size automatically to fit full screen.
OSD H-Position This function moves the OSD menu window left or right.
OSD V-Position This function moves the OSD menu window up or down.
This function is to choose a display that allows maximum graphics text
quality. The resolution selection can either be 640 x 400 or
Graph Text
720 x 400. Please refer to Chapter 3 “ Standard Timing” Table for of
different timing modes.
The recall function will return all adjusted parameters to factory preset
Recall
values.
Five OSD language options are available:
Language
English, German, French, Spanish and Italian.
Press the left or right Adjustment Control button to select other language.
Color
Color Temp.: Push the (+ -) button to select a different color temperature.
Please see the diagram below for function and description.
Temperature
Save Exit
Saves the values of this setting and exits the OSD menu function.
Icon
Function
Description
CIE coordinated Color Temperature of
9300°K
Sets the CIE coordinate color temperature to
9300°K
9300
SRGB
User
CIE coordinated Color Temperature of
SRGB°K
Sets the CIE coordinate color temperature to
SRGB°K
Three colors (Red, Green, Blue) can be Sets the settings to a by user defined CIE
adjusted from the OSD menu Temperature.
5
Chapter 3 Technical Information
Specifications
LCD Panel
Size
Hannstar
15.0" (38 cm)
Display Type
Resolution
Active matrix color TFT LCD
1024 x 768
Display Dot
Display Area (mm)
Display Color
Brightness
Contrast Ratio
Response Time
Lamp Voltage
Lamp Current
Viewing Angle
1024 x (RGB) x 768
304 x 228 (H x V)
262K
200 cd/m2 (typical)
400:1 (typical)
35 ms (typical)
730 Vrms (typical)
6.5 mA rms. (typical)
Vertical: -55° ~ +45°
Horizontal: -65° ~ +65°
Display Colors
Video
Input Signal
16.7M with FRC or Dithering
Analog RGB 0.7Vp-p
Input Impedance
Polarity
75 Ohm ± 2%
Positive, Negative
Amplitude
Multi-mode Supported
(0 - 0.7)-0.035V/+0.07V
Horizontal Frequency: 24 ~ 61 KHz
Vertical Frequency: 55 ~ 75 Hz
Control
Power
On/Off switch with LED indicator
OSD
Brightness
Contrast
Digital
Digital
Horizontal Position
Vertical Position
Phase
Digital
Digital
Digital
Clock
Digital
Display Mode Setup
OSD Format
Use EEPROM to save settings in memory
20 characters x 9 rows
Power Management
Mode
Power Consumption*
AC Input
LED Color
On
Standby
Suspend
Off
30W maximum
240 VAC
240 VAC
240 VAC
240 VAC
240 VAC
Green
Yellow
Yellow
Yellow
Dark
3W maximum
3W maximum
3W maximum
3W maximum
DC Power Off
Yellow: Standby, Suspend, Off
Dark: DC Power off
Disconnected
3W maximum
240 VAC
* Meeting VESA DPMS requirements measured from AC Input end of AC adapter.
Sync Input
Signal
Separate TTL compatible horizontal and vertical synchronization
Polarity
Positive and negative
6
Plug & Play
Supports VESA DDC1 and DDC2B functions
External Connection
Power Input (AC input)
Video Cable
AC socket
1.5M with 15-pin D-sub connector
Environment
Operating Condition:
Temperature
5°C to 40°C/41°F to 104°F
Relative Humidity 20% to 80%
Temperature
-20°C to 60° C/-4°F to140° F
Storage Condition:
Relative Humidity 5% to 85%
Power Supply (AC Input)
Input Voltage
Input Current
Single phase, 100 ~ 240VAC, 50 / 60 Hz
1.5 A maximum
Size and Weight
Dimensions
Net Weight
Gross Weight
353 (W) x 346 (H) x 204 (D) mm
3 ± 0.3 kg (6.6 ± 0.66lbs)
4.5 ± 0.3 kg (9.9 ± 0.66lbs)
Pin Assignment
6
Signal
Signal
Description
PIN
Description
PIN
1
2
3
4
5
6
7
8
Red
Green
Blue
Digital GND
Digital GND
Red Rtn
Green Rtn
Blue Rtn
9
+5V
11
1
5
10
11
12
13
14
15
PC Detect
Digital GND
SDA
H. Sync.
V. Sync.
SCL
15
10
Standard Timing Table
If the selected timing is NOT included in table below, this LCD monitor will use the most suitable
available timing.
H. Freq.
V. Freq.
Pixel Freq.
H/V Sync.
Polarity
Resolution
Mode
VGA-350
(KHz)
31.469
24.830
(Hz)
70.087
56.420
(MHz)
25.175
21.050
640 x 350
640 x 400
+/-
-/-
NEC PC9801
VGA-400-GRAPH NEC
PC9821
640 x 400
31.469
70.087
25.175
-/+,-/-
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024x 768
1024x 768
1024x 768
1024x 768
31.469
37.861
37.500
31.469
35.156
37.879
48.077
46.875
49.725
48.363
53.964
56.476
60.023
59.940
72.809
75.000
70.087
56.250
60.317
72.188
75.000
74.55
60.004
66.132
70.069
75.029
25.175
31.500
31.500
28.322
36.000
40.000
50.000
49.500
57.2832
65.000
71.664
75.000
78.750
-/-
-/-
-/-
-/+
+/+
+/+
+/+
+/+
-/-
VGA-480
VESA - 480 - 72Hz
VESA - 480 - 75Hz
VESA-400-TEXT
SVGA
VESA-600-60 Hz
VESA-600-72 Hz
VESA-600-75 Hz
APPLE MAC-800
XGA
-/-
+/+
-/-
COMPAQ-XGA
VESA-768-70 Hz
VESA-768-75 Hz
+/+
7
Troubleshooting
This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing
differences among various VGA cards in the market, users may initially experience an unstable or
unclear display whenever a new display mode or new VGA card is selected.
Attention
This LCD Monitor Supports Multiple VGA Modes.
Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor.
PROBLEM
Picture is unclear and unstable
The picture is unclear and unstable, please perform the following steps :
1. Enter PC to “Shut Down Windows” status while you’re in MS-Windows environment.
2. Check the screen to see if there’s any black vertical stripes appear. If there are, take advantage of
the “Clock” function in OSD menu and adjust (by increment or decrement numbers) until those
bars disappear.
3. Move to “Phase” function in OSD menu again and adjust the monitor screen to its most clear
display.
4. Click “No” on “Shut Down Windows” and back to the normal PC operating environment.
PROBLEM
There is no picture on LCD Monitor
If there’s no picture on the LCD Monitor, please perform the following steps:
1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the
system is running on the correct timing. Refer to Chapter 3 for information on timing.
2. Turn off the LCD Monitor and then turn it back on again. If there is still no picture, press the
Adjustment Control button several times.
3. If step 2 doesn’t work, connect your PC system to another external CRT. If your PC system
Functions properly with a CRT Monitor but it does not function with the LCD Monitor, the output
timing of the VGA card may be out of the LCD’s synchronous range. Please change to an
alternative mode listed in the Standard Timing Table or replace the VGA card, and then repeat
steps 1 and 2.
PROBLEM
There is no picture on LCD Monitor
If you have chosen an output timing that is outside of the LCD Monitor’s synchronous range
(Horizontal: 24 ~ 61 KHz and Vertical: 56 ~ 75 Hz), the OSD will display a “Out of Range” message.
Choose a mode that is supported by your LCD Monitor.
Also, if the signal cable is not connected to LCD monitor at all or properly, the monitor screen will
display a message “No Input Signal”.
8
|