Owner’s Manual
PPHP1259
There is an integrated 35mm speaker stand
adapter on the bottom side of the cabinet. Use the
knob to secure the speaker to the stand.
Connections
Your PPHP1259 speaker has a speakon jack as well as a ¼” jack. The
jacks are wired in parallel, which allows you to daisy chain additional
speakers. Thus you can use one amplifier channel to power multiple
speakers.
Make certain that the wires you are using are at least 12 gauge
unshielded speaker cable (the lower the number, the thicker the wire). Do
not use shielded “instrument” cables.
Hooking speakers up in parallel decreases the overall
impedance, placing a greater load on the amplifier. Check your
amplifier’s specifications to ensure that you are not overloading
the channel.
CAUTION: DO NOT USE MORE THAN ONE JACK AS AN
AMPLIFIER INPUT. DOING SO WILL DAMAGE THE SPEAKER!
Amplifier Requirements
There are a couple of considerations to keep in mind when choosing
an amplifier to drive your PPHP1259. While it is true that an amplifier with
a higher power rating can damage the drivers, under-powering can be even
more dangerous. When an amplifier is overdriven and starts distorting, it
generates transient frequencies that are much louder than the program
material. These wayward frequencies could damage your speaker. A proper
match is an amplifier which could drive the speaker up to the cabinet’s RMS
rating, without exceeding the amplifier’s own RMS level.
www.pyleaudio.com
3
Operation
When powering on your equipment, make sure the volume level on
the amplifier is turned all the way down. This is to avoid the “popping”
noise, which could damage your speaker.
The placement of speakers can be a bit tricky. Besides for the
practical considerations, there are acoustic issues as well. Avoid placing the
speaker in a corner, as this will cause the low frequencies to sound “muddy”.
Similarly, but to a lesser degree, placing the speaker directly against the wall
will exaggerate the low frequencies. You should therefore try to place your
speaker so that it is a few feet away from the wall.
High frequencies are unidirectional while low frequencies are omni
directional. Being that this is a full range enclosure, it is important that the
speaker be placed so that the high frequencies reach the intended listeners
properly. Make certain that no person or object could come to interrupt the
line-of-site between the loudspeaker and the audience.
When using more than one loudspeaker, you have to account for
phase alignment. When the speakers are close together this is not usually an
issue. However, when they are far apart, the sound from one speaker may
reach the ear a fraction of a second before the other. This will cause certain
frequencies to cancel out, resulting in a hollow sound. To avoid this, you
may have to use a delay processor to align the sound from the speakers.
www.pyleaudio.com
4
Troubleshooting
No Sound:
VCheck connections
VTry a different speaker cable
VCheck levels on amplifier
VConfirm amplifier is getting a signal (check signal LED, or use
headphone output)
Intermittent Output:
VCheck connections
VTry a different speaker cable
Weak Bass:
VCheck the polarity of the speaker connection. It may be reversed.
VListen with headphones to confirm the amplifier is being sent a good
signal.
Distorted Sound:
VCheck if the amplifier is overdriven. If it is, you will have to turn the
level down.
VMake sure you are not exceeding the RMS rating of your speaker.
Specifications
Frequency
Range
Sensitivity
(1w/1m)
Model
Woofer
Tweeter
RMS
Peak
Connections
Ω
Dimensions
W = 16.1“
Weight
30 lb.
12“
Kapton
Voice Coil Midrange/Tweeter
13“ x 7“ Titanium
Super Horn
Speakon (1)
³″ (1)
PPHP1259
47-18 kHz 250W 500W
92 dB
8Ω D = 12“
H = 22.6“
5
Recommended Accessories
PT Series
PSTND1
°Loading Capacity: 100 lbs.
°Tubing Diameter: 1.5“
°Black Anodized Stand
°Telescopes To Six Feet
Amplifiers
°
°
°
Professional High-Power amplifiers
8 Models to choose from
All models rack-mountable
in standard ISO 19“ rack
PPJJ30
°30ft. 12 Gauge
°Professional Speaker Cable
°³“ to ³“
PZR Series
Amplifiers
°
°
°
Professional High-Power amplifiers
3 Models to choose from
PPJJ15
°Same as above 15ft.
All models rack-mountable
in standard ISO 19“ rack
PPSS30
°30ft. 12 Gauge
°Professional SpeakerCable
°Speakon to Speakon
PDMK101
°
°
°
°
°
(2) 21 ft. 12 Gauge Cable
Speakon to Speakon
Carrying Bag
PPSS15
°Same as above 15ft
Telescopes to Six Feet
Loading Capacity 100 lbs.
PPSJ30
°30ft. 12 Gauge Professional
°Speaker Cable
°Speakon to ³“
PPSJ15
°Same as above 15ft.
www.pyleaudio.com
7
|